Showing 5 results for Characterization
K. Christine Stella, A. Samson Nesaraj,
Volume 7, Issue 2 (6-2010)
Abstract
Abstract:
as magnetic materials, semiconductors, pigments, catalysts, refractories and electronic ceramics. In this paper, we
reported the preparation of NiAl
The resulting powder was chracterized by XRD, particle size analysis and SEM. The XRD patterns show that the
combustion technique was excellent to prepare single – phased cubic NiAl
found to be around 14 nm. From the particle size analysis, it was found that the 50 % of the particles lie below 30
µm. The micrographs show the formation of fluffy agglomerates composed of fine particles.
Spinels constitute an advanced group of materials with great technologial appeal, being able to be applied2O4 spinels by low temperature combustion technique using glycine and urea as fuels.2O4 particles and the crystallite sizes were
M. Akbarzadeh, A. Shafyei, H. R. Salimijazi,
Volume 12, Issue 1 (3-2015)
Abstract
In the present study, CrN, TiN and (Ti, Cr)N coatings were deposited on D6 tool steel substrates. Physical and mechanical properties of coatings such as microstructure, thickness, phase composition, and hardness were evaluated. Phase compositions were studies by X-ray diffraction method. Mechanical properties were determined by nano-indentation technique. The friction and wear behaviour of the coatings were investigated using ball-on-disc tests under normal loads of 5, 7 and 9 N at sliding distance of 500 m, at room temperature. Scanning electron microscope equipped with energy dispersive spectroscopy, optical microscope, and 2D/3D profilometry were utilized to investigate the microstructures and wear mechanisms. Wear test results clarified that the wear resistance of (Ti, Cr)N and TiN coatings was better than that of CrN coating. The wear resistance of the (Ti, Cr)N coatings was related to the Ti content in the coatings and reduced by decreasing the Ti content. The dominant wear mechanisms were characterized to be abrasive and tribochemical wear
H. Jafarian, H. Miyamoto,
Volume 17, Issue 1 (3-2020)
Abstract
In the present work, accumulative roll bonding (ARB) was used as an effective method for processed of nano/ultrafine grained AA6063 alloy. Microstructural characteristics indicate considerable
grain refinement leading to an average grain size of less than 200 nm after 7 ARB cycles. Texture analysis showed that 1-cycle ARB formed a strong texture near Copper component ({112}<111>). However, texture transition appeared by increasing the number of ARB cycles and after 7-cycle of ARB, the texture was mainly developed close to Rotated Cube component ({100}<110>). The results originated from mechanical properties indicated a substantial increment in strength and microhardness besides a meaningful drop of ductility after 7 ARB cycles.
Seyedali Seyedmajidi, Maryam Seyedmajidi,
Volume 19, Issue 2 (6-2022)
Abstract
Recently, using calcium phosphates and at the top of them, hydroxyapatite (HA) has been considered in medical and dental applications as an artificial biomaterial due to their chemical and structural similarity to the bodychr('39')s skeletal tissues such as bone and tooth. Because of reinforcement of hydroxyapatitechr('39')s mechanical and biological properties by substitution of OH- groups by F- ions to produce fluorapaptite (FA) has been proven, in this article synthesis methods, properties and medical applications of fluorapatite and its pros and cons in comparison with hydroxyapatite have been reviewed.
Pravin Jadhav, R.s.n Sahai, Deepankar Biswas, Asit Samui,
Volume 20, Issue 4 (12-2023)
Abstract
The present work deals with the effect of Multi-walled Carbon Nanotube (MWCNT) and functionalized (carboxyl and amine) MWCNT on the mechanical properties of the PAEK (Poly Aryl Ether Ketone) polymer composite. The MWCNT and functionalized (carboxyl and amine) MWCNT concentration varied as 0.25, 0.5 and 0.75 weight percentages. Compositeswere prepared by using a melt compounding method using a twin-screw extruder and all testing samples were prepared using an injection molding machine as per American Society for Testing and Materials (ASTM) standards. Samples were tested for tensile strength, impact strength, flexural strength, heat deflection temperature, hardness, and density. There is an increase in the tensile strength, impact strength, flexural strength, and heat deflection temperature, with percentage increase in filler loading up to 0.5 %, followed by decrease in it with higher filler loading. The increase is maximum for amine functionalized MWCNT.
