Search published articles


Showing 4 results for Grain Size
THE EFFECT OF COOLING RATE AND AUSTENITE GRAIN SIZE ON THE AUSTENITE TO FERRITE TRANSFORMATION TEMPERATURE AND DIFFERENT FERRITE MORPHOLOGIES IN MICROALLOYED STEELS
M. Esmailian,
Volume 7, Issue 1 (3-2010)
Abstract

Abstract:

transformation temperature and different ferrite morphologies in one Nb-microalloyed (HSLA) steel has been

investigated. Three different austenite grain sizes were selected and cooled at two different cooling rates for obtaining

austenite to ferrite transformation temperature. Moreover, samples with specific austenite grain size have been

quenched, partially, for investigation on the microstructural evolution.

In order to assess the influence of austenite grain size on the ferrite transformation temperature, a temperature

differences method (TDM) is established and found to be a good way for detection of austenite to ferrite, pearlite and

sometimes other ferrite morphologies transformation temperatures.

The results obtained in this way show that increasing of austenite grain size and cooling rate has a significant influence

on decreasing of the ferrite transformation temperature.

Micrographs of different ferrite morphologies show that at high temperatures, where diffusion rates are higher, grain

boundary ferrite nucleates. As the temperature is lowered and the driving force for ferrite formation increases,

intragranular sites inside the austenite grains become operative as nucleation sites and suppress the grain boundary

ferrite growth. The results indicate that increasing the austenite grain size increases the rate and volume fraction of

intragranular ferrite in two different cooling rates. Moreover, by increasing of cooling rate, the austenite to ferrite

transformation temperature decreases and volume fraction of intragranular ferrite increases.

The effect of different austenite grain size and different cooling rates on the austenite to ferrite
EFFECTS OF Al-5TI-1B MASTER ALLOY AND HEAT TREATMENT ON THE MICROSTRUCTURE AND DRY SLIDING WEAR BEHAVIOR OF AN Al-12Zn-3Mg-2.5Cu ALLOY
M. Alipour, S. Mirjavadi, M. K. Besharati Givi, H. Razmi, M. Emamy, J. Rassizadehghani,
Volume 9, Issue 4 (12-2012)
Abstract
In this study the effect of Al–5Ti–1B grain refiner on the structural characteristics and wear properties of Al–12Zn–3Mg–2.5Cu alloy was investigated. The optimum amount for Ti containing grain refiners was selected as 2 wt.%. T6 heat treatment, (i.e. heating at 460 °C for 1 h before water quenching to room temperature and then aging at 120 °C for 24 h) was applied for all specimens before wear testing. Dry sliding wear resistant of the alloy was performed under normal atmospheric conditions. The experimental results showed that the T6 heat treatment considerably improved the resistance of Al–12Zn–3Mg–2.5Cu alloy to dry sliding wear.
The Influence of Milling Parameters on Surface Properties in Milled AZ91C Magnesium Alloy
Amir Mostafapour, Milad Mohammadi, Ali Ebrahimpour,
Volume 18, Issue 2 (6-2021)
Abstract
A full factorial design of experiment was applied running 36 experiments to investigate the effects of milling parameters including cutting speed with three levels of 62.83, 94.24 and 125.66 m/min, feed rate with three levels of 0.1, 0.2 and 0.3 mm/tooth, cutting depth with two levels of 0.5 and 1 mm and machining media with two levels, on surface integration properties of magnesium AZ91C alloy such as grain size, secondary phase percent, surface microhardness and surface roughness. In all cases, a fine grained surface with higher secondary phase sediment and microhardness obtained comparing the raw material. According to analysis of variance results, the most effective parameter on grain size, secondary phase percent and microhardness was cutting depth and the most effective parameter on surface roughness was feed rate. although the grain size in all machined samples was smaller than that of the raw material but due to the dual effect of cryogenic conditions, which both cool and lubricate and reduce the temperature and strain rate at the same time, the direct effect of this parameter on grain size was not significant. Also, the all interaction effects of parameters on grain size and microhardness were significant.
Johnson–Mehl–Avrami–Kolmogorov (JMAK-type) Analysis of Deformation-Induced Martensitic Transformation in AISI 304L Stainless Steel
Mohammad Javad Sohrabi, Hamed Mirzadeh, Saeed Sadeghpour, Reza Mahmudi,
Volume 20, Issue 4 (12-2023)
Abstract
Deformation-induced α΄-martensite generally forms at shear bands in the coarse-grained austenite, while it nucleates at grain boundaries in the ultrafine-grained (UFG) austenite. The available kinetics models are related to the nucleation on the shear band intersections, and hence, their application to investigating the kinetics of α΄-martensite formation for the UFG regime cannot be justified. Accordingly, in the present work, the general Johnson–Mehl–Avrami–Kolmogorov (JMAK-type) model was implemented for comparing the kinetics of α΄-martensite formation in the UFG and coarse-grained regimes using an AISI 304L stainless steel. On the experimental front, the X-ray diffraction (XRD) patterns and the electron backscattered diffraction (EBSD) maps were used for phase and microstructural analyses, respectively. It was revealed that the simple JMAK-type model, by considering the dependency of the volume fraction of α΄-martensite on the strain, is useful for modeling the experimental data, predicting the nucleation sites based on the theoretical Avrami exponents, and characterizing the transformation kinetics at low and high strains.
Page 1 from 1     

© 2022 All Rights Reserved | Iranian Journal of Materials Science and Engineering

Designed & Developed by : Yektaweb