Sajad Ghaemifar, Hamed Mirzadeh,
Volume 20, Issue 4 (12-2023)
Abstract
Phase transformations and the evolution of hardness during elevated-temperature annealing of Inconel 718 superalloy manufactured by the laser powder bed fusion (L-PBF) were investigated. The microstructural evolution, elemental analysis, phase formation, and hardening were characterized by scanning electron microscopy, energy-dispersive spectroscopy, X-ray diffraction, and Vickers indentation test, respectively. It was observed that the effect of annealing treatments is directly governed by the annealing parameters (i.e. time and temperature), for which the hardness measurement as a fruitful and convenient tool can reveal this effect. The increase of the hardness, which was obtained by the annealing (aging) treatments at the temperature range of 800-900 °C, indicated precipitation of the Ni3Nb γ˝ strengthening phase; while owing to the coarsening of precipitates as a results of overaging at this temperature range, the hardness decreased. For instance the length and aspect ratio of precipitates in the aged sample at 800 °C for 1 h is 67.14 nm and 0.32, respectively; while these values in the aged sample at 800 °C for 8 h is 78.34 nm and 0.44, respectively. On the other hand, the decrease of the hardness at temperatures of 950 and 1000 °C was attributed to the decrease of dislocation density in conjunction with the Ni2Nb Laves phase dissolution. Hence, it is crucial to determine the annealing parameters according to the required microstructure and properties.
Adeel Hassan,
Volume 20, Issue 4 (12-2023)
Abstract
Friction stir additive manufacturing (FSAM) is a variant of sheet lamination additive manufacturing used to produce large, near-net-shaped 3D parts. Unlike traditional friction stir lap welding, FSAM introduces a new plate to one that is already joined, with the effective area limited to the nugget zone. The present study focuses on exploring the microstructure and microhardness around the nugget zone in a five-plate AA 7075-T651 laminate synthesized at 1000 rpm and 35 mm/min. Microhardness increased vertically in the weldment NZ, reaching 143 HV in the top layer with 2.0 μm fine equiaxed grains. The grains on the advancing and retreating sides were coarser compared to the nugget zone. A W-shaped microhardness profile appeared across layer interfaces. These findings contribute significantly to advancing the FSAM technique, particularly in manufacturing multi-layered, multi-pass laminates.
Tumelo Moloi, Thywill Cephas Dzogbewu, Maina Maringa, Amos Muiruri,
Volume 21, Issue 3 (9-2024)
Abstract
The stability of microstructure at high temperatures is necessary for many applications. This paper presents investigations on the effect of changes in temperature on the microstructures of additively manufactured Ti6Al4V(ELI) alloy, as a prelude to high temperature fatigue testing of the material. In the present study, a Direct Metal Laser Sintering (DMLS) EOSINT M290 was used to additively manufacture test samples. Produced samples were stress relieved and half of these were then annealed at high temperatures. The samples were then heated from room temperature to various temperatures, held there for three hours and thereafter, cooled slowly in the air to room temperature. During tensile testing, the specimens was heated up to the intended test temperature and held there for 30 minutes, and then tensile loads applied to the specimens till fracture. Metallographic samples were then prepared for examination of their microstructures both at the fracture surfaces and away from them. The obtained results showed that changes in temperature do have effects on the microstructure and mechanical properties of Ti6Al4V(ELI) alloy. It is concluded in the paper that changes in temperature will affect the fatigue properties of the alloy.
Mohammad Derakhshani, Saeed Rastegari, Ali Ghaffarinejad,
Volume 22, Issue 1 (3-2025)
Abstract
In this research, the morphology of the Ni-W coating was modified by adding graphene oxide (GO) nanosheets in such a way that a foam-like structure with high porosity and holes in the form of intertwined tunnels was obtained. Different amounts of GO nanosheets were added to the plating bath and the resulting coating was examined. In order to estimate the electrochemically active surface area, the cyclic voltammetry (CV) test was used. Moreover, the linear polarization test (LSV) and chronoamperometry in 1 M NaOH were conducted to investigate the electrocatalytic activity for the hydrogen evolution reaction (HER). It was found that by adding 0.4 g/L GO to the electroplating bath, the electrocatalytic properties are doubled and the active surface of the electrode is significantly increased.
Amin Rahiminejad, Mojgan Heydari, Fariba Tajabadi,
Volume 22, Issue 1 (3-2025)
Abstract
Targeted drug delivery systems have been developed to overcome the disadvantages of conventional drug delivery systems and folate is one of the targeting molecules that has received attention in recent years. The attachment of this molecule to the surface of niosomal carriers has been achieved using Castor oil as an intermediate molecule. We synthesized caster folate (CF) and incorporate to noisome structure as biocompatible component for targeted delivery of anticancer drug Doxorubicin. This research studies the novelty of castor folate ester in the scope of niosome-based drug delivery systems. The aim was to investigate the feasibility of manufacturing and evaluating a niosomal carrier containing the drug doxorubicin hydrochloride (DOX) and its targeting by the combination of CF. The results of Fourier Transform Infrared Spectroscopy (FTIR) confirm chemical bounding between folic acid and castor oil. SEM showed good morphology with spherical structure of niosomes. These niosomes have particles size of 330 to 538 nm for different samples. Also, zeta potential was -28 to -40 mV that results good stability. The addition of CF to niosomal samples increased wettability and drug loading efficacy and along with DLS and zeta potential results confirms the folate impact on surface hydrophilicity of niosome spheres. The prepared formulations increased the effectiveness of doxorubicin on L929 fibroblast cells. The proposed biocompatible component showed the role of CF in the architectural integrity of niosomal lipid bilayers.
